Water expands when it freezes, and your RV's water lines have no room to absorb the pressure. A single cup of water left in a water line, a pump head, or a water heater tank can crack a fitting, split a PEX line, or ruin a pump. The damage usually stays hidden until spring, when you turn the water on and find a wet floor.
Winterizing is the fix, and it is not complicated. Most RV owners can do it in an afternoon with a few basic winterizing supplies.
This guide walks through the full process: draining the water system, bypassing the water heater, protecting the lines with RV antifreeze or compressed air, and getting the rest of the rig ready for cold storage.
If you are new to this, read it start to finish. If you have done it before, skip to the step you need.
In this article:
- How to winterize an RV: step by step
- What you will need
- When to winterize your RV
- Beyond the plumbing
- Common mistakes that lead to freeze damage
How to Winterize an RV: Step by Step
This is the core of the job. Work through it in order.
- Turn off the water heater and let it cool. Never drain a hot or pressurized tank. Give it several hours, or overnight if you just used it. Turn off the electric element and the propane, and disconnect from city water.
- Empty the holding tanks. Dump the black tank first, then the gray, so the gray water rinses the hose. Flush the black tank if you have a built-in flush system. The goal is tanks as empty and clean as you can get them, since whatever is left sits there until spring.
- Drain the fresh water tank. Open its drain valve and let it run out completely.
- Drain the water heater. Remove the anode rod or nylon drain plug and let the tank empty. Open the pressure relief valve so it drains faster. Rinse out sediment with a tank wand if you have one, then reinstall the plug with fresh Teflon tape.
- Open the low point drains. Most RVs have two, one hot and one cold, under the coach. Open every faucet inside and out, including the shower and outside shower, and run the water pump briefly to clear the lines. Shut the pump off as soon as it runs dry so you do not damage it.
- Close the drains and faucets. Once everything has run out, close them back up.
- Remove the water filter cartridge. Antifreeze should not run through a filter. Take out the cartridge and leave the housing empty, or install the bypass plug if your system has one.
- Set the water heater to bypass. This is the step people forget. Without a bypass, you will pump 6 to 10 gallons of antifreeze into the tank and waste the whole case. Turn the bypass valves per your kit, then verify the hot side is isolated.
The system is now drained and the water heater is isolated. Next, clear the water still sitting in the lines using one of the two methods below. Both methods finish the same way, with the traps and the toilet.

Method A: Pump in RV Antifreeze
This is the most common approach and the most forgiving.
- Install a water pump converter kit, or disconnect the pump's inlet line and attach a siphon hose.
- Drop the hose into a gallon of RV antifreeze and turn on the pump.
- Open each fixture one at a time, hot side then cold side, until pink antifreeze runs steady.
- Do not skip the outside shower, the toilet sprayer, the washing machine lines, and the refrigerator ice maker line if you have one.
- Turn off the pump and open a faucet briefly to release pressure.
Most RVs take 2 to 3 gallons. A larger fifth wheel with a washer hookup can take more.
Method B: Blow out the Lines with Compressed Air
This method uses no antifreeze in the lines, but it leaves more room for error because small amounts of water can stay trapped in low spots.
- Attach a blow-out plug to the city water inlet and connect your compressor.
- Keep the regulator at or below 40 psi. Higher pressure can damage fittings and fixtures.
- Open one fixture at a time, hot and cold, until only air comes out. Cycle back through them a second time, since water tends to settle back.
- Air does not protect the drains or the toilet seal, so finish with the step below.
Many owners use both: blow the lines out first, then pump antifreeze through. That combination is the most reliable protection in a hard freeze.
Last Step, for Either Method: Fill the Traps and the Toilet
Neither method protects the drains. Water sits in the P-trap under every sink and in the shower drain, and the toilet's flush valve seal dries out and cracks if it is left bare.
- Pour about a cup of RV antifreeze down each sink drain and the shower drain.
- Pour a cup or two into the toilet and flush until pink antifreeze shows in the bowl.
- Add some to the black and gray tanks through the drains so any residual water at the valves is protected.
Do not Forget These
- Outside shower and its hose
- Toilet sprayer
- Ice maker supply line
- Washer and dryer hookups
- Water filter housing
- Any aftermarket filtration or water softener
What You Will Need

Here is the full parts list for the job. Check it before you start, or order ahead so everything is on the shelf when the first cold front shows up.
Everyone Needs These Items
- RV antifreeze (non-toxic) - Protects the lines, traps, and toilet seal. Plan on 2 to 3 gallons if you are pumping it through the lines, or 1 gallon if you are using compressed air and only treating the drains.
- Socket or wrench for the drain plug - Suburban and Mor-Flo steel tanks use a 1-1/16 inch anode rod. Atwood and Dometic aluminum tanks use a nylon plug that takes a different socket. Check which one your heater has.
-
Teflon tape - For resealing the anode rod or drain plug on reinstall.
If you are Pumping Antifreeze (Method A)
- Water pump converter kit or siphon hose - Lets the onboard pump draw antifreeze straight from the jug. A converter kit is the cleaner permanent solution; a siphon hose works if you are comfortable disconnecting the pump inlet.
If you are Blowing the Lines out (Method B)
- Blow-out plug - Adapts your air hose to the city water inlet.
-
Air compressor with a regulator - You need to hold pressure at or below 40 psi. A small pancake compressor is plenty.
Check Before you Buy
- Water heater bypass kit - Most modern RVs already have a factory bypass. Look behind the water heater for two or three valves on the hot and cold lines before ordering one. If yours has no bypass, you need a kit.
-
Replacement water filter cartridge - You pull the old cartridge out during winterizing and leave the housing empty. The new one goes in when you de-winterize in the spring, so buy it whenever it is convenient.
Nice to Have
- Holding tank cleaner or treatment - Not required, but it keeps waste residue from drying onto the tank walls and sensors over several months of storage.
-
Water heater tank rinse wand - Makes it easier to flush sediment out while the tank is drained.
Not sure which drain plug or bypass kit fits your unit? Check your water heater model number before ordering. Our parts staff can confirm the right one if you call it in.
When to Winterize Your RV
Here in North Texas the first freeze usually arrives in the second half of November, so plan to winterize by early November. Cold fronts have brought freezes as early as October.
A few guidelines:
- Below 32 degrees for several hours is enough to start freezing exposed lines. Underbelly plumbing and outside shower lines go first.
- An enclosed, heated underbelly buys you time, not immunity. It only helps while you are plugged in with the furnace running. If the RV is unplugged or the furnace is off, treat it like any uninsulated rig.
- If the RV is going into storage for the season, winterize it at the end of your last trip. Do not wait for the forecast.
If a freeze is coming tonight and you are not ready, the fastest protection is to drain everything you can, open all faucets and low point drains, and leave them open. That is not a complete job, but a drained line has far less water to expand.
Beyond the Plumbing
Freeze damage gets the attention, but a few more hours of prep protects the rest of the RV through storage.
Batteries

- Charge lead-acid batteries fully before storage. A discharged lead-acid battery can freeze and crack; a fully charged one holds up well.
- Disconnect the negative terminal or pull the battery disconnect switch. Parasitic draws from detectors and control boards will flatten a battery over a few months.
- Check the charge every month or two, or leave it on a maintainer.
- Lithium (LiFePO4) batteries are different. Store them around half charge, keep them disconnected, and do not charge them below freezing. Check your battery's manual for its specific storage range.
Tires
- Inflate to your RV’s placard pressure, not the sidewall number. The sidewall figure is the tire’s maximum, not the right pressure for your load. For heavy rigs, use the tire manufacturer’s inflation table for your axle weight.
- Cover the tires. UV exposure degrades tires faster than cold does.
- If you can, park on wood or pads instead of bare concrete.
Seals and Roof
- Walk the roof if it is rated for it, or inspect from a ladder. Look at the sealant around vents, skylights, the AC shroud, and the front and rear caps.
- Reseal any cracked or lifting lap sealant. Water that gets in under snow and ice has all winter to spread.
- Check sidewall seams, window frames, and the entry door.
Pests
- Remove all food, including sealed pantry items. Mice chew through packaging.
- Seal entry points with steel wool or expanding foam, especially around the underbelly, wiring pass-throughs, and the furnace area.
- Leave cabinets and drawers open so air moves through.
Propane and Appliances
- Turn the propane off at the tank.
- Prop the refrigerator and freezer doors open and wipe them dry. A closed, damp fridge grows mold.
- Clean the oven and microwave so nothing attracts pests.
Storage
- Retract slide-outs and clean and treat the seals first.
- Close the roof vents, or install vent covers that let air move while keeping rain out.
- Use a breathable RV cover, not a plastic tarp. Tarps trap moisture against the sidewalls and can abrade the finish in wind.
- Indoor or covered storage is the easiest option if you have access to it.
Common Mistakes That Lead to Freeze Damage
These are the ones we hear about most often at the parts counter in the spring.
- Skipping the water heater bypass. You end up with a tank full of antifreeze and empty jugs, and the lines still are not fully protected.
- Using automotive antifreeze. Automotive coolant is typically ethylene glycol and is toxic. Only non-toxic RV antifreeze, usually propylene glycol, belongs in a potable water system.
- Forgetting the outside shower. It sits in an exposed compartment and freezes early.
- Running the water pump dry too long. Pumps need the fluid for cooling and lubrication. Shut it off as soon as the lines clear.
- Blowing out lines at too high a pressure. Anything much above 40 psi puts stress on fittings and fixtures.
- Leaving water in the P-traps. Air blowing through the lines does nothing for the traps under your sinks and shower.
- Assuming a heated underbelly is enough. It helps while you are plugged in and running the furnace. It does nothing in unpowered storage.
-
Leaving a battery connected and partly discharged. It can freeze and crack the case.
Winterize Once, Sleep Easy All Season
Winterizing takes an afternoon. A cracked water line, a split pump, and the water damage that comes with them take a lot more than that, and you will not find out until spring.
Work through the steps in order, double-check the water heater bypass, and do not skip the drains. If you are unsure which parts fit your rig, confirm your water heater model number before you order.

Comments (0)
There are no comments for this article. Be the first one to leave a message!